This email is only intended to be read by the named recipient. It may contain information which is confidential,
proprietary or the subject of legal privilege. If you are not the intended recipient you must delete this email and may
not use any information contained in it. Legal privilege is not waived because you have read this email.
2
Permit No.: AK/H/17/2579
Additional Conditions
1.
Separate Plant - The carriage or towing of separate items of plant, equipment or materials not specifically nominated in the
description of load is not permitted.
2.
Mass - The mass of any axle shall not exceed the mass specified in this permit. The gross mass of the vehicle or combination of
vehicles must not exceed the limit specified on the current certificate of loading issued to the vehicles.
3.
Authorised Agent - The vehicle shall not be operated on a road or bridge under this permit when in the opinion of an
authorised agent of the road controlling authority, as communicated to the operator, it would be contrary to public interest to do so.
4.
Non Transferable - This permit is not transferable either to other users of or to any vehicle other than the vehicle described by
this permit.
5.
Weighing - Police are authorised to divert vehicles up to five kilometres from the approved route for the purpose of weighing,
provided under strength bridges are not included on the route.
6.
Identification Sign - The vehicle shall display a high-productivity motor vehicle sign in accordance with Clause 5.10 of the Land
Transport Rule (41001): Vehicle Dimensions and Mass 2016 when operating as a high-productivity motor vehicle.
7.
Trailer Roll Stability Control (RSC) – The trailer(s) if first registered on or after 1 May 2010, must have roll stability control
fitted and active; that is an Electronic Brake System (EBS) with the roll stability control function turned on. Alternatively, if the
trailer(s) were first registered before 1 May 2010 or are log trailers carting round wood first registered before 1 April 2016 and do not
have EBS and RSC – these must instead operate with a minimum Static Roll Threshold (SRT) of 0.4g, provided SRT compliance
documentation is kept with the permit and produced to enforcement officers.
Page 2 of 4
Printed: 18/07/2017 13:20
Permit No.: AK/H/17/2579
Revocation
This permit can be revoked, under
clause 5.7 of the Rule.
Authorised Issuing Officer
..........................................
(Signature)
Joseph Hillary
(Name)
18 July 2017...........
(Date)
Permit Issuing Officer
(Designation)
(for) NZ Transport Agency
(Controlling Authority)
Auckland
(Location)
123245 – 14 July 2017
(Permit Dated)
Note:
1. This permit is an exemption from the mass limits set out in the Land Transport Rule (41001): Vehicle Dimensions and Mass 2016,
and does not authorise the user to exceed the exemption so permitted or exempt the user from complying with all other acts,
regulations and other laws (including those relating to certificate of loading and road user charges or Static Roll Threshold).
2. This permit must be carried on the vehicle, and must be surrendered for inspection on the demand of any enforcement officer, or an
authorised agent of the NZ Transport Agency or a road controlling authority.
3. The conditions on the reverse of this form shall apply together with any other conditions on the attached sheets.
4.
Overdimension - For the transport of vehicles and loads that exceed the limits specified in Section 6 of the Land Transport Rule
(41001): Vehicle Dimensions and Mass 2016, a separate permit must be obtained from the Overdimension Permit Issuing Agency
(OPIA) at the Transport Registry Centre, Palmerston North. OPIA contact number 0800 OVERSIZE / 0800 683774.
5.
Railway Level Crossings - Travel over level crossings is not fully covered by this permit. Operators of overweight and
overdimension vehicles may require permission from KiwiRail or their agents for travel over railway level crossings.
6.
Tyre Pressures - Tyres must be operated at the pressure recommended by either the manufacturer or the Tyre and Rim Associations
but not exceeding the maximum pressure stated in the Land Transport Rule 32013: Tyres and Wheels 2001.
Fees Payable:
Permit Issuing Fee (As specified in Schedule 4A of the Heavy Motor Vehicle Regulations 1974)
$54.55
Total Fee
$54.55
GST
$8.18
Total
$62.73
Page 4 of 4
Printed: 18/07/2017 13:20
